One of the more fun projects that I've tackled lately has been customizing some IKEA Billy bookcases for a client. I've got the skinny on how it came together, in case you'd like to try something similar. I don't have the glamour-shot "after" photos yet with the perfect styling and the new rug so I'll be sure to update this post when I do.
We started with four of IKEA's ubiquitous Billy bookcases in a space off of their kitchen that was newly designated as a library.
They had just purchased new comfy reading chairs and wanted to use their existing pedestal table. I created a moodboard, or collaged image, of what their space could look like with some changes. We knew we wanted a new rug and lighting above the bookcases, as well as some fun detailed woodwork.
We were on track for a cosy area to read and relax, except for one minor detail. Behind all of those bookcases was a length baseboard heating, causing the bookcases to sit out from the wall about 6" and not allowing us to anchoring the bookcases to the wall to prevent toppling. So I built a base or platform for the bookcases to sit on from 2 x 4s bolted securely into the framing of the house and the floor below. This ensured that there was no weight on the heater itself and that the bookcases would be supported and flush against the wall. I also ran electricity from the existing outlet to a new switch that would be hidden inside a shelf and a new outlet near the ceiling for the lights that would be installed above the bookshelves.
Here are all four bookcases securely fastened to both the newly-constructed base and the wall behind them. They are also screwed to each other in a number of places for stability and to keep all of the front edges even. I used metal L braces on both sides of the bottom of each bookcase to secure them to the 2 x 4s that they're sitting on. I like to build things rock solid with no possibility of failure, so I add fail-safes wherever I can think of them. It might be overkill, but I sleep better.
You can see one light in place as a test, and the new outlet peeking out above the third bookcase. The homeowner had made a hole for a power strip in that same bookcase, but it didn't end up being in the right place for the new switch (which is camouflaged just to the right of it) so that got patched.
Once the bookcases were secured I created a soffit above with a frame of 1x2 pines and added painted planks of wood in different colors, trimmed it out with moulding, and installed the four new lights. The switch inside the bookshelf behind a picture frame controls the lights. I loaded all of the books back on the shelves, staged the table with a vase and flowers, and stood back to admire the work so far.
So the top of the bookshelves looks great, the bookshelves themselves look fabulous, but the bottom is looking a bit unfinished. To remedy this, first I trimmed out the opening below each bookcase with pine and stained it to match the bookcases' finish. I also stained all of the visible parts of the 2 x 4s that make up the base (which hadn't happened yet in the photo below).
Because I wanted the heat from the baseboards to be able to reach the room (there is a wood burning stove just out of sight to the left, so it is really warm there, but still), I purchased metal grating to cover the openings below the bookcases without blocking the heat. I cut them to size and spray painted them oil-rubbed bronze. Those got nailed in place. Then I added trim around each of the grates, mitering the corners.
The fronts of the bookcases were also trimmed out in lathing strips over the areas where two bookcases meet vertically so that the units appeared more custom and built in. You could no longer see four individual bookcases, but rather one large unit. I added a 1 x 12" pine board to the left side of the last bookcase, notching around the baseboard, to complete the custom look (not pictured, but I'll take one from that angle the next time I'm there and post it). In retrospect, I should have painted the baseboard heaters (and maybe the floor inside the base) a dark brown color so they wouldn't be noticeable through the grating.
After using wood putty to fill of the nail holes, I stained everything with a Kona brown stain to match the existing finish on the Billy bookcases. It's hard to remember that the actual bottom of the bookcases is way up in the air, hidden under all of the trim work. Stay tuned for the stunning "after" photos!